Development of design charts for stress intensity factors at tips of multi-site cracks in unstiffened curved panels

Multi-site damage need to be addressed and evaluated in order to assess the integrity of aging aircraft structures. One of the problems recognized in the recent times is the effect of interaction between two or more cracks in the close neighborhood in such structures. The present paper deals with such a problem and presents numerical estimates of stress intensity factors at a crack tip in an un-stiffened curved panel with a secondary crack in the vicinity of a primary crack. The results are presented in the form of design charts. These results should be useful in evaluation in the damage tolerance evaluation of aircraft structures with multi-site damage. (C) 2014 Elsevier Ltd. All rights reserved.

Statistical analysis of the position of the monsoon trough

Using surface charts at 0330GMT, the movement df the monsoon trough during the months June to September 1990 al two fixed longitudes, namely 79 degrees E and 85 degrees E, is studied. The probability distribution of trough position shows that the median, mean and mode occur at progressively more northern latitudes, especially at 85 degrees E, with a pronounced mode that is close to the northern-most limit reached by the trough. A spectral analysis of the fluctuating latitudinal position of the trough is carried out using FFT and the Maximum Entropy Method (MEM). Both methods show significant peaks around 7.5 and 2.6 days, and a less significant one around 40-50 days. The two peaks at the shorter period are more prominent at the eastern longitude. MEM shows an additional peak around 15 days. A study of the weather systems that occurred during the season shows them to have a duration around 3 days and an interval between systems of around 9 days, suggesting a possible correlation with the dominant short periods observed in the spectrum of trough position.

An accurate method for the experimental evaluation of the acoustical impedance of a black box

Among different methods, the transmission-line or the impedance tube method has been most popular for the experimental evaluation of the acoustical impedance of any termination. The current state of method involves extrapolation of the measured data to the reflecting surface or exact locations of the pressure maxima, both of which are known to be rather tricky. The present paper discusses a method which makes use of the positions of the pressure minima and the values of the standing-wave ratio at these points. Lippert's concept of enveloping curves has been extended. The use of Smith or Beranek charts, with their inherent inaccuracy, has been altogether avoided. The existing formulas for the impedance have been corrected. Incidentally, certain other errors in the current literature have also been brought to light.Subject Classification: 85.20.

Finite element analysis of rotors

A finite element formulation for the natural vibration analysis of tapered and pretwisted rotors has been presented. Numerical results for natural frequencies for various values of the geometric parameters and rotational speeds, have been computed for the case of rotors with and without pretwist. A Galerkin solution for the fundamental has also been worked out and has been used to provide a comparison for the finite element results. Charts for rapid estimation of the fundamental frequency parameter of tapered rotors, have been included.

Optimum design of cantilever sheet pile walls in sandy soils using inverse reliability approach

In this paper an approach for obtaining depth and section modulus of the cantilever sheet pile wall using inverse reliability method is described. The proposed procedure employs inverse first order reliability method to obtain the design penetration depth and section modulus of the steel sheet pile wall in order that the reliability of the wall against failure modes must meet a desired level of safety. Sensitivity analysis is conducted to assess the effect of uncertainties in design parameters on the reliability of cantilever sheet pile walls. The analysis is performed by treating back fill soil properties, depth of the water table from the top of the sheet pile wall, yield strength of steel and section modulus of steel pile as random variables. Two limit states, viz., rotational and flexural failure of sheet pile wall are considered. The results using this approach are used to develop a set of reliability based design charts for different coefficients of variation of friction angle of the backfill (5%, 10% and 15%). System reliability considerations in terms of series and parallel systems are also studied.

Target reliability based design optimization of anchored cantilever sheet pile walls

In this study, the stability of anchored cantilever sheet pile wall in sandy soils is investigated using reliability analysis. Targeted stability is formulated as an optimization problem in the framework of an inverse first order reliability method. A sensitivity analysis is conducted to investigate the effect of parameters influencing the stability of sheet pile wall. Backfill soil properties, soil - steel pile interface friction angle, depth of the water table from the top of the sheet pile wall, total depth of embedment below the dredge line, yield strength of steel, section modulus of steel sheet pile, and anchor pull are all treated as random variables. The sheet pile wall system is modeled as a series of failure mode combination. Penetration depth, anchor pull, and section modulus are calculated for various target component and system reliability indices based on three limit states. These are: rotational failure about the position of the anchor rod, expressed in terms of moment ratio; sliding failure mode, expressed in terms of force ratio; and flexural failure of the steel sheet pile wall, expressed in terms of the section modulus ratio. An attempt is made to propose reliability based design charts considering the failure criteria as well as the variability in the parameters. The results of the study are compared with studies in the literature.

Correlation of thermodynamic properties of chloromethanes

A correlation for entropy and enthalpy based on the two-parameter law of corresponding states and the reference substance concept has been obtained. For 199 points tested, the over-all average absolute deviation and the maximum deviations in the calculated values of entropy with the available data are 0.74 and 7.20%. The corresponding deviations of enthalpy are 1.86 and 15.0%, respectively. A compressibility chart for chloromethanes has been made and shown to be superior to existing charts. For 102 points tested, the average absolute and maximum deviations in the compressibilities were 1.80 and 19.5%, respectively.

Analysis of the performance characteristics of a two-inertia power transmission system with a plate clutch

The performance of a plate clutch in a two-inertia power transmission system is analysed assuming negligible compliance and using a piecewise linear function to represent the clutch torque characteristic. Expressions defining, for all linear segments of the clutch torque characteristic, dimensionless input and output velocities of the clutch and dimensionless slip period are presented. The use of these expressions in preparing design charts to aid analysis and design of the plate clutch is outlined.

An Eventful Synthetic Approach Towards the Biologically Potent Natural Product Ottelione A: Enantio-, Regio- and Stereoselective Construction of the Bicyclic Core

A novel synthetic approach towards the recently reported anti-tumor and anti-tuberculor natural product ottelione A from the readily available Diels-Alder adduct of cyclopentadiene and p-benzoquinone is delineated. Our short strategy, besides being enantio-, regio- and stereoselective, charts an eventful course and is inherently well-suited for adaptation towards diverse synthetic analogues of this biologically potent natural product.

Analysis of heat and mass transfer during bulk hydraircooling of spherical food products

Hydraircooling is a technique used for precooling food products. In this technique chilled water is sprayed over the food products while cold unsaturated air is blown over them. Hydraircooling combines the advantages of both air- and hydrocooling. The present study is concerned with the analysis of bulk hydraircooling as it occurs in a package filled with several layers of spherical food products with chilled water sprayed from the top and cold unsaturated air blown from the bottom. A mathematical model is developed to describe the hydrodynamics and simultaneous heat and mass transfer occurring inside the package. The non-dimensional governing equations are solved using the finite difference numerical methods. The results are presented in the form of time-temperature charts. A correlation is obtained to calculate the process time in terms of the process parameters.

Passive pressure coefficients, critical failure surface and its kinematic admissibility

Using a combination of a logarithmic spiral and a straight line as a failure surface, comprehensive charts have been developed to determine the passive earth pressure coefficients and the positions of the critical failure surface for positive as well as negative wall friction angles. Translational movement of the wall has been examined in detail, considering the soil as either an associated flow dilatant material or a non-dilatant material, to determine the kinematic admissibility of the limit equilibrium solutions.

Exergetic analysis of carbon dioxide vapour compression refrigeration cycle using the new fundamental equation of state

The purpose of this paper is to present exergy charts for carbon dioxide (CO2) based on the new fundamental equation of state and the results of a thermodynamic analysis of conventional and trans-critical vapour compression refrigeration cycles using the data thereof. The calculation scheme is anchored on the Mathematica platform. There exist upper and lower bounds for the high cycle pressure for a given set of evaporating and pre-throttling temperatures. The maximum possible exergetic efficiency for each case was determined. Empirical correlations for exergetic efficiency and COP, valid in the range of temperatures studied here, are obtained. The exergy losses have been quantified. (C) 2003 Elsevier Ltd. All rights reserved.

New static 3-step distance relay

A new static 3-step distance relay based on the principle of multi-input phase comparison is described in the paper. Design principles and typical discriminating and logic circuits are described for the new relaying system. The relaying system uses semiconductor circuits throughout and features high speed and good performance. The comparator model, which effects multi-input phase comparison, has been devised to provide reliable pickup for closein faults, and to achieve an improved polar characteristic in the complex- impedance plane, which fits around only the fault area of a transmission line. Operating time of the relay is less than 1 cycle for unbalanced faults, and less than a halfcycle for 3-phase faults. Protective circuits have also been added to detect power swing and to block tripping for a predetermined number of power-swing cycles. The operating characteristics of the relay, as expressed by accuracy/range charts, are presented.